Senior
Foremen
Education:
-Completion of Higher Secondary Education plus 3 years Diploma in
Automobile Engineering or equivalent.
-Fairly spoken and written English and Arabic languages.
Experience & Skills:
-Minimum 7 to 15 years experience in Repairing, Maintenance &
Overhauling of Heavy Earthmoving Equipments like Dozer, Loader, Excavator,
caterpillar, Komatsu, Heavy Duty Cranes, & Heavy Duty Vehicles like
Trailer, Truck Vehicles etc.
-Knowledge of welding techniques, special workshop tools i.e. tires
changing machine, hydraulic press.
-Can operate all types of equipment.
-Should possess a valid Qatari heavy Duty Driving License.
Technician
Education
-Completion of full time secondary education, followed by a minimum of
two years (ITI / Diploma) full time training in instrument maintenance,
electronic and microprocessor equipment to Ordinary National Certificate level,
except where good background and experience is advantageous especially relating
to the oil and gas production industry, including gas compression. Any relevant
courses to be taken into consideration.
-Fair knowledge of English, in both written and spoken.
Experience
-Minimum 4 years experience in the maintenance and repair of wide range
of instrumentation, electronic, pneumatic, gas turbine and gas compression control
and protection systems, logic microprocessor based control equipment.
-Should have a good knowledge of safety practices relating to the Oil
& Gas / Petrochemical industry.
Primary Purpose of the Job
Installs, cleans, calibrates, maintains, modifies, overhauls,
re-commissions and tests all installed instrumentation and control systems,
including pneumatic and electronic process control instrumentations as per the
instruction by Senior Tech / Instrument Engineer. Assist in the maintenance and
fault finding, repair and calibration of gas turbine controls and protection
systems in accordance with prescribed routine and preventive maintenance
procedures. Carry out effective maintenance offield instruments including
routine inspection, Testing, calibration, repair, maintenance, commissioning
and liaise with production personnel fault diagnosis and maintenance of
instrument related to gas turbine Control Systems, Vibration & Temperature
monitoring & Protection systems, Anti- surge control systems, HMI, PLC /
SLC
Principal Accountabilities
-Carry out effective maintenance of field instruments including routine
inspection, Testing, calibration, repair and maintenance, commissioning. Carry
out breakdown repair, maintenance and calibration of electronic and pneumatic
instruments in site or in workshop. This shall include, but not be restricted
to work, F&G detectors, electronic transmitter for various process
measurements, pneumatic transmitters and controllers, stand alone controllers,
Control valves of different types, shutdown and blow down valves of different
types including pneumatic actuators, Solenoid valves, SDVIBDV related panel
instruments, UP converters, level transmitter, temperature transmitter, local
indicators, analytical Instruments.
-Carry out preventive Maintenance Jobs. Helps Senior Tech to Collect
& Maintain
Necessary documents related to corrective, Preventive Maintenance.
Involves in making the work permit and carry out the required work as per the
work order.
-Witness function tests, loop checks and verifies data sheets, reports
and documents as instructed by Senior technician/Instrument Engineer.
-For instruments that cannot be repaired on site, assist in arranging to
transport to central instrument workshop. This includes testing and calibration
as well as isolating, removing, dismantling, inspecting, calibrating,
repairing, testing, installing and commissioning of all the instruments
mentioned.
-Carry out onsite fault diagnosis of gas turbine control systems, gas
compressors control systems including anti surge control system. This will
involve checking and trouble shooting of systems, field instruments,
vibrations, displacements and temperature instrumentation. Routine maintenance
of control systems and field instruments.
-Carry out minor modification works along with general technicians Carry
out Pre shutdown, Shutdown activities as per planned schedules and contracts
-Carry out Fault diagnosis DCS Systems PLC ESD and F&G and
associated field instrumentation, Carry out effective maintenance by doing
routine inspection, calibration, repair and maintenance of Toxic and flammable
gas detectors, Testing of flame detectors and heat detectors
-At the start of each shift as instructed by senior technician!
Instrument Engineer, perform the corrective / preventive / breakdown
maintenance. Follow safe and proper working practices in preparing permit to
work for all worksites. Liaise with production operations personnel. Reports
general/senior technicians as and when required for updating jobs and plant
status.
-Ensure worksites & related equipments are left clean, tidy &
sealed before leaving worksite. Ensure that the plant is left in a safe
condition where it is necessary to carry over the work to the next shift and
maintain good house keeping. Follow proper time keeping and attendance.
-Carry out jobs as per ISO / QMS procedures & maintain
Documentation.
General
Technicians
Education
-Completion of full time secondary education, followed by a minimum of
two years (ITI / Diploma) full time training in instrument maintenance,
electronic and microprocessor equipment to Ordinary National Diploma level,
except where good background and experience is advantageous especially relating
to the oil and gas production industry, including gas compression. Any relevant
courses to be taken into consideration. Fair knowledge of English, in both
written and spoken
Experience
-Minimum 7 years experience in the maintenance and repair of wide range
of instrumentation, electronic, pneumatic, gas turbine and gas compression
control and protection systems, logic microprocessor based control equipment.
-Should have a good knowledge of safety practices relating to the
Oil/Petrochemical industry.
Primary Purpose of the Job
Forms part of a team with a crew of technicians in carrying out the
routine preventative maintenance of process control systems and equipment
including electronic and pneumatic instrumentation. Includes dismantling,
inspecting, calibrating, repairing, testing, installing and commissioning a
wide range of field instrument equipment. Carries out repair work on turbine
control panels and assists in the repair work of small pneumatically controlled
instruments and valves. Ensures all work is carried out in a safe, timely and
cost effective manner and according to planned schedules and procedures.
Principal Accountabilities
-Participates with a crew of technicians in carrying out the routine
preventative maintenance of process control instrumentation. Including repair,
maintenance and calibration of electronic and pneumatic instruments in site or
in area workshop.
-Troubleshoot logic circuit of turbine control system, DeS, PLC, ESD
system and maintain Fire & gas systems and associated flame detectors,
flammable gas detectors, toxic gas detectors, heat detectors, Testing, isolating,
removing, dismantling, inspecting, repairing, calibrating, installing and
commissioning of the full range of electronic and pneumatic instrumentation
used in the hydrocarbon industry.
-Repair and calibrate electronic transmitters (SMART and conventional),
pneumatic transmitters and controllers, solenoid valves, pneumatic actuated
valves, liP converters, level, pressure, flow, temperature transmitters, local
indicators (pressure and temperature etc.) in the field and workshop.
-Repair and maintenance of various types of control valves, shutdown
valves, blow down valves on site.
-Witness function tests, loop checks and verifies data sheets, reports
and documents as instructed by Senior technician/Instrument Engineer
-Carries out repair work on turbine control panels ESD and Fire and gas
panel PLC and DCS panel in emergency requests and / or engineering Work Orders
requiring Hot/Cold
Work Permits. Replace defective relays, solenoid valves, solid-state or
relay logic instrumentation as identified during inspection.
-Participates with Technician-l in the repair of pneumatically
controlled instruments and valves as required, ability to read instructions
from technical manuals and manufacturers recommendations.
-Carry out instrument control equipment inspections at field locations.
Receives emergency requests to attend to the defective instruments. Liaises
with production Supervisors to arrange plant access and issuing of appropriate
permits and either repairs on-site, replaces unit or removes and returns to
central instrument workshop for repair and testing.
-Documentation - Calibration sheets, Test equipment inventory, hand
tools inventory, pressure test records, inspection reports, daily activity
reports. All these shall be completed as and when required.
